2024 Drinking Water Report

Each year, the City of Eden Prairie issues the results of monitoring done on its drinking water to advance consumers’ understanding of drinking water and heighten awareness of the need to protect precious water resources.

The monitoring results in this report cover the period from Jan. 1 through Dec. 31, 2024.

To reduce the environmental impact of producing this report, the City of Eden Prairie provides the annual Drinking Water Report in an online version only.

Compliance with National Drinking Water Regulations

The City of Eden Prairie provides drinking water to its residents from a groundwater source. This includes 15 wells ranging from 381 to 420 feet deep, that draw water from the Prairie Du Chien-Jordan and Jordan aquifer formations.

In order to ensure that tap water is safe to drink, the U.S. Environmental Protection Agency (EPA) prescribes regulations which limit the amount of certain contaminants in water provided by public water systems. Food and Drug Administration (FDA) regulations establish limits for contaminants in bottled water which must provide the same protection for public health.

Drinking water, including bottled water, may reasonably be expected to contain at least small amounts of some contaminants. Keep in mind that be definition, anything present in drinking water that is not a molecule of oxygen and hydrogen, must be described as a contaminant (something other than a molecule of water). The presence of contaminants does not necessarily indicate that water poses a health risk. More information about contaminants and potential health effects can be obtained by calling the EPA's Safe Drinking Water Hotline at 800-426-4791.

Some people may be more vulnerable to contaminants in drinking water than the general population. Immuno-compromised persons, such as persons with cancer undergoing chemotherapy, persons who have undergone organ transplants, people with HIV/AIDS or other immune system disorders, some elderly and infants, can be particularly at risk from infections. The developing fetus and therefore pregnant women may also be more vulnerable. These people should seek advice about drinking water from their health care providers. EPA/CDC guidelines on appropriate means to lessen the risk of infection by Cryptosporidium and other microbial contaminants are available from the Safe Drinking Water Hotline at 800-426-4791.

Drinking Water Sources

Minnesota’s primary drinking water sources are groundwater and surface water. Groundwater is the water found in aquifers beneath the surface of the land. Groundwater supplies 75% of Minnesota’s drinking water. Surface water is the water in lakes, rivers, and streams above the surface of the land. Surface water supplies 25% of Minnesota’s drinking water.

Contaminants can get in drinking water sources from the natural environment and from people’s daily activities. There are five main types of contaminants in drinking water sources.

Microbial contaminants, such as viruses, bacteria and parasites. Sources include sewage treatment plants, septic systems, agricultural livestock operations, pets and wildlife.
Inorganic contaminants include salts and metals from natural sources (e.g., rock and soil), oil and gas production, mining and farming operations, urban stormwater runoff and wastewater discharges.
Pesticides and herbicides are chemicals used to reduce or kill unwanted plants and pests. Sources include agriculture, urban stormwater runoff, and commercial and residential properties.
Organic chemical contaminants include synthetic and volatile organic compounds. Sources include industrial processes and petroleum production, gas stations, urban stormwater runoff and septic systems.
Radioactive contaminants such as radium, thorium and uranium isotopes come from natural sources (e.g., radon gas from soils and rock), mining operations, and oil and gas production.

The Minnesota Department of Health (MDH) provides information about Eden Prairie's drinking water source(s) in a source water assessment, including:

How the City protects it's drinking water source(s)
Nearby threats to Eden Prairie's drinking water sources
How easily water and pollution can move from the surface of the land into drinking water sources, based on natural geology and the way wells are constructed

If you wish to obtain the entire source water assessment, please call 651-201-4700 during normal business hours. View the source water assessment report online.

How to Read Water Quality Data Tables

The tables below show the contaminants which were found last year or the most recent time they were sampled for. They also show the levels of those contaminants and the Environmental Protection Agency’s (EPA) limits. Substances which were tested for but not found are not included in the tables.

Some contaminants are sampled for less than once a year because the levels are not expected to change from year to year. If any of these contaminants were found the last time they were sampled for, they are included in the tables below with the detection date.

The City may have done additional monitoring for contaminants that are not included in the Safe Drinking Water Act. To request a copy of these results, call the Minnesota Department of Health at (MDH) 651-201-4700 between 8 a.m. and 4:30 p.m., Monday through Friday.

Some contaminants are monitored regularly throughout the year and rolling (or moving) annual averages are used to manage compliance. Because of this averaging, there are times where the Range of Detected Test Results for the calendar year is lower than the Highest Average or Highest Single Test Result, because it occurred in the previous calendar year.

Abbreviations are listed at the bottom of this report.

Testing and Monitoring Procedures

Questions

Contact Rick Wahlen, utility operations manager, at 952-949-8530 with questions and information about the City's drinking water, opportunities for public participation in decisions that may affect the quality of water, or to learn about volunteering for the lead and copper household water testing program.

If you wish to learn more about scheduling a tour of the Water Treatment Plant, the City's lawn watering policies or would like a copy of this report, please contact Joe Dusek, water treatment plant supervisor, at 952-294-5902.

Water Quality Monitoring Results

The City works with the Minnesota Department of Health (MDH) to test drinking water for more than 100 contaminants. It is not unusual to detect contaminants in small amounts. No water supply is ever completely free of contaminants. Drinking water standards protect Minnesotans from substances that may be harmful to their health.

Regulated Substances

Lead and Copper (Tested at Customer Taps)

Contaminant (date, if sampled in previous year)	EPA's Ideal Goal (MCLG)	EPA's AL	90% of Results Were Less Than	Homes with High Levels	Range of Detected Test Results	Violation	Typical Sources
Lead (7/14/22)	0	90% of homes less than 15 ppb	0.93 ppb	0 out of 30	0-5.4 ppb	No	Corrosion of household plumbing
Copper (7/14/22)	0	90% of homes less than 1.3 ppm	0.01 ppm	0 out of 30	0-.02 ppm	No	Corrosion of household plumbing

If present, elevated levels of lead can cause serious health problems, especially for pregnant women and young children. You may be in contact with lead through paint, water, dust, soil, food, hobbies or your job. There is no safe level of lead.

Lead in drinking water is primarily from materials and components associated with service lines and home plumbing. The City of Eden Prairie is responsible for providing high quality drinking water and removing lead pipes from service lines, but cannot control the variety of materials used in plumbing components.

Find more information about protecting yourself from lead in drinking water at the bottom of this report.

Inorganic and Organic Contaminants (Tested in Drinking Water)

Contaminant (date, if sampled in previous year)	EPA's Ideal Goal (MCLG)	EPA's Limit (MCL)	Highest Average or Highest Single Test Result	Range	Violation	Typical Sources
Barium (7/27/20)	2 ppm	2 ppm	0.03 ppm	N/A	No	Discharge of drilling wastes; discharge from metal refineries; erosion of natural deposit.
Cis-1,2- Dichloroethene (cis-1,2-dichloroethylene)	70 ppb	70 ppb	0.62 ppb	N/A	No	Discharge from chemical and agricultural chemical factories.

Contaminants Related to Disinfection (Tested in Drinking Water)

Substance (date, if sampled in previous year)	EPA's Ideal Goal (MCLG)	EPA's Limit (MCL)	Highest Average or Highest Single Test Result	Range	Violation	Typical Sources
Total Trihalomethanes (TTHMs)	N/A	80 ppb	57.9 ppb	41.10–57.9 ppb	No	Byproduct of drinking water disinfection.
Total Haloacetic Acids (HAA)*	N/A	60 ppb	7.3 ppb	5–7.3 ppb	No	Byproduct of drinking water disinfection.
Total Chlorine	4 ppm	4 ppm	1.06 ppm	0.85–1.2 ppm	No	Water additive used to control microbes.

*Total HAA refers to HAA5

Other Substances (Tested in Drinking Water)

Substance (date, if sampled in previous year)	EPA's Ideal Goal (MCLG)	EPA's Limit (MCL)	Highest Average or Highest Single Test Result	Range	Violation	Typical Sources
Flouride	4 ppm	4 ppm	0.59 ppm	0.54–0.58 ppm	No	Erosion of natural deposits; water additive to promote strong teeth.

Fluoride is nature's cavity fighter, with small amounts present naturally in many drinking water sources. There is an overwhelming of credible, peer-reviewed, scientific evidence that fluoridation reduces tooth decay and cavities in children and adults, even when there is availability of fluoride from other sources, such as fluoride toothpaste and mouth rinses. Since studies show that optimal fluoride levels in drinking water benefit public health, municipal community water systems adjust the level of fluoride in the water to an optimal concentration between 0.5 to 0.9 parts per million (ppm) to protect your teeth. Fluoride levels below 2.0 ppm are not expected to increase the risk of a cosmetic condition known as enamel fluorosis.

Unregulated Substances

In addition to testing drinking water for contaminants regulated under the Safe Drinking Water Act, the City sometimes also monitors for contaminants that are not regulated. Unregulated contaminants do not have legal limits for drinking water. MDH, EPA and other health agencies may have developed comparison values for some of these compounds. Some of these comparison values are based solely on potential health impacts and do not consider the City's ability to measure contaminants at very low concentrations nor the cost and technology of prevention and/or treatment. These values may be set at levels that are costly, challenging or impractical for a water system to meet (for example, large-scale treatment technology may not exist for a given contaminant). Sample data are listed along with comparison values in the table below; it is important to note that these comparisons values are not enforceable.

Detection alone of a regulated or unregulated contaminant should not cause concern. The meaning of a detection should be determined considering current health effects information. We are often still learning about the health effects, so this information can change over time.

A person drinking water with a contaminant at or below the comparison value would be at little to no risk for harmful health effects. If the level of a contaminant is above the comparison value, people of a certain age or with special health conditions-like a fetus, infants, children, elderly, and people with impaired immunity—may need to take extra precautions. We are notifying you of the unregulated contaminants we have detected as a public education opportunity.

In the past year, Eden Prairie's drinking water may have tested for additional unregulated contaminants as part of the Fifth Unregulated Contaminant Monitory Rule (UCMR 5) and results are still being processed. The UCMR 5 Datafinder allows people to easily search for, summarize and download the available UCMR 5 analytical results.

Unregulated Contaminants (Tested in Drinking Water)

Contaminant	Comparison Value	Highest Average Result or Highest Single Test Result	Range of Detected Test Results
Manganese (2020)	100 ppb	1.52 ppb	N/A
Sodium*	20 ppm	11.4 ppm	N/A
Sulfate	500 ppm	25.3 ppm	N/A
Perfluorobutanoic Acid (PFBA)	7000 ppt	11.7 ppt	10.7 -12.7 ppt

*Note that home water softening can increase the level of sodium in your water.

More Information

Key to Abbreviations

AL — Action Level: The concentration of a contaminant which, if exceeded, triggers treatment or other requirement which a water system must follow.

MCL — Maximum Contaminant Level: The highest level of a contaminant that is allowed in drinking water. MCLs are set as close to the MCLGs as feasible using the best available treatment technology.

MCLG — Maximum Contaminant Level Goal: The level of a contaminant in drinking water below which there is no known or expected risk to health. MCLGs allow for a margin of safety.

MRDL — Maximum Residual Disinfectant Level: The highest level of a disinfectant allowed in drinking water. There is convincing evidence that the addition of a disinfectant is necessary for control of microbial contaminants.

MRDLG — Maximum Residual Disinfectant Level Goal: The level of a drinking water disinfectant below which there is no known or expected risk to health. MRDLGs do not reflect the benefits of the use of disinfectants to control microbial contaminants.

N/A — Not Applicable (does not apply).

ppt — Parts per trillion: One part per trillion in water is like one drop in one trillion drops of water, or about one drop in a swimming pool. This can also be expressed as nanograms per liter (ng/l).

ppb — Parts per billion: One part per billion in water is like one drop in one billion drops of water, or about one drop in a swimming pool. This can also be expressed as micrograms per liter (ug/l).

ppm — Parts per million: One part per million in water is like one drop in one million drops of water, or about one cup in a swimming pool. This can also be expressed as milligrams per liter (mg/l).

PWSID — Public water system identification.

Other Information

Conservation

Below are some tips to help you conserve water – and save money in the process.

Fix running toilets—they can waste hundreds of gallons of water.
Turn off the tap while shaving or brushing your teeth.
Shower instead of bathe. Bathing uses more water than showering, on average.
Only run full loads of laundry and set the washing machine to the correct water level.
Only run the dishwasher when it is full.
Use water-efficient appliances (look for the WaterSense label).
Use water-friendly landscaping, such as native plants.
When you do water your yard, water slowly, deeply, and less frequently. Water early in the morning and close to the ground.

Learn more

U.S. Environmental Protection Agency: WaterSense

Educational Opportunities

Environmental Learning Center

The Eden Prairie Water Treatment Plant has an outstanding Environmental Learning Center and tours are offered for students wishing to learn more about public water systems. Learn more and schedule a tour.

Minnesota North College

Programs on Ely campus include a 60-credit-hour AAS in Water Quality Science as well as a 35-credit-hour diploma in Water Operations to prepare students for a career in either treatment or distribution operations with any public works department in the country. Learn more about this program or call 800-657-3608.

St. Cloud Technical and Community College

SCTCC's Water Environment Technologies Training 10-month certificate program or 14-month associates degree program provide students with the skills for jobs in drinking and wastewater treatment, as well as water and sewer maintenance. Learn more about this program or call 320-308-5952.

St. Paul College

St. Paul College offers the Water Utility Treatment and Technology course two nights per week in nine separate modules. Each 10-week class provides students with skills for jobs in water and wastewater. Learn more about this program or call 651-846-1800.

Reduce Backflow at Cross Connections

Bacteria and chemicals can enter the drinking water supply from polluted water sources in a process called backflow. Backflow occurs at connection points between drinking water and non-drinking water supplies due to water pressure differences.

The Minnesota Department of Health and American Water Works Association recommend the following:

Do not submerge hoses in buckets, pools, tubs or sinks.
Keep the end of hoses clear of possible contaminants.
Do not use spray attachments without a backflow prevention device. Attach these devices to threaded faucets. Such devices are inexpensive and available at hardware stores.
Use a licensed plumber to install backflow prevention devices.
Maintain air gaps between hose outlets and liquids. An air gap is a vertical space between the water outlet and the flood level of a fixture (e.g., the space between a wall-mounted faucet and the sink rim). It must be at least twice the diameter of the water supply outlet, and at least one inch.
Commercial property owners should develop a plan for flushing or cleaning water systems to minimize the risk of drawing contaminants into uncontaminated areas.

Protect Yourself from Lead

Read below to learn how you can protect yourself from lead in drinking water.

Let the water run before drinking tap water and to flush your pipes for several minutes by running your tap. If you have a lead service line, you may need to let the water run longer. A service line is the underground pipe that brings water from the main water pipe under the street to your home.
- Activities such as taking a shower, doing laundry or dishes help keep water moving in your home system but are not a replacement for running the tap before you drink if it has not been used for a long period of time.
- The only way to know if lead has been reduced by letting it urn is to check with a test. If letting the water run does not reduce lead, consider other options to reduce your exposure.
Know your service line materials by contacting your public water system, or you can search for your address online at the Minnesota Lead Inventory Tracking Tool.
- Protect your tap: A quick check for lead in EPA's step by step guide to learn how to find lead pipes in your home.
Use cold water for drinking, making food and making baby formula. Hot water releases more lead from pipes than cold water.
Test your water. In most cases, letting the water run and using cold water for drinking and cooking should keep lead levels low in your drinking water. If you are still concerned about lead, arrange with a laboratory to test your tap water. Testing your water is important if young children or pregnant women drink your tap water.
Treat your water if a test shows your water has high levels of lead after you let the water run. You an use a filter certified with ANSI//NS standards 53 and 42 for lead reduction.

View the websites below to find information on lead in drinking water, testing methods and steps you can take to minimize exposure.

Service Line Inventory

Eden Prairie has nearly completed and submitted the City's service line materials inventory to the MDH. Use the Lead Inventory Tracking Tool to view the inventory or contact JDusek@edenprairie.org.

To complete the service line inventory, the City documented residential service lines during the water meter replacement project. As of Oct. 8, 2024, Eden Prairie's inventory contains 0 lead, one galvanized requiring replacement, 3,673 unknown materials and 15,529 non-lead service lines.

Water Conservation Rebate Programs

Water Softening

The City of Eden Prairie uses a lime-softening water treatment process that removes most of the calcium and magnesium from the water, resulting in softened water. Raw water drawn from the aquifer has a total hardness of 380 parts per million (ppm). After the water travels through the lime-softening plant, the total hardness is reduced to 90 ppm.

Some of the benefits Eden Prairie residents receive from softened water include:

Increased efficiency for soaps and detergents
Reduction in mineral staining on fixtures
Softer skin and clean, smooth hair
Fabrics that are softer, last longer and stay whiter
Increased lifespan of water appliances such as ice makers, dishwashers, water heaters and clothes washers
No need to maintain your own water softener
Lower cost per gallon than public water which is not softened by the utility
No salt brine discharge to the wastewater system, minimizing impacts to the environment